49 SECTION 49: COOLING SYSTEM

Part number changes for Rotax oil cooler, other misc changes and improvements.

Changelog

• 11/24/2021
  • KAI Page 49-01 REV 3: “ROTAX OIL COOLER” was “886 004 OIL COOLER”
  • KAI Page 49-02 REV 3: In Step 2, “Cut 2.0 in [50.8 mm] from the end of one of the FF-1208C Expansion Springs. Deburr the ends…” was “Deburr the ends…”
  • In Step 3, “Insert the longer FF-1208C inside of the FF-1208A and the shorter FF-1208C inside of the FF-1208B in the location called out in Figure 1. “ was “Insert a FF-1208C Expansion Spring inside of the FF-1208A Radiator Hose – Input and FF-1208B Radiator Hose – Output in the location called out in Figure 1.”
  • In Figure 1, “30 [76.2 cm] FF-1208A, 20 [50.8 cm] FF-1208B” was “30 FF-1208A, 20 FF-1208B”.
  • In Figure 1, “1 [25.4 mm], BOTH, FF-1208A & FF-1208B” was “1, BOTH, FF-1208A & FF-1208B”.
  • In Figure 2, “8 3/16, [207.6 mm]” was “8 3/16”, “7 1/2, [190.5 mm]” was ”7 1/2”, “8, [203.2 mm]” was “8”, “1, [25.4 mm]” was “1”.
  • KAI Page 49-11 REV 4: In Step 10, “Tilt the oil cooler to keep…” was “Tilt the 886 004 Oil Cooler to keep…”
  • In Figures 1 & 2, “OIL COOLER” was “886 004”
  • KAI Page 49-14 REV 5: In Step 12, “…the label printed on Page 49-19…” was “…the label printed on Page 49-21…”
  • KAI Page 49-17 REV 4: “NOTE: It is important to install the hoses without the lines being pushed or twisted into position. When the cowling is removed the lines will then hold the oil cooler in position; which…“ was “Note: It is important to install the hoses without the lines being pushed or twisted into position. When the cowling is removed the lines will then hold the 886 034 Oil Cooler in position; which…”
  • In Step 1, “Remove the lower nut holding the Cylinder #1 Exhaust Pipe and install…” was “Remove the lower nut holding the EXH-1201 Cylinder #1 Exhaust Pipe and install…”
  • In Step 2, “…and the Left Oil Cooler Nipple (finger tight) as shown…” was “…and the left oil cooler nipple of the 886 034 Oil Cooler (finger tight) as shown…”
  • In Step 3, “…between the Right Oil Cooler Nipple (finger tight) and the…” was “…between the right oil cooler nipple of the 886 034 Oil Cooler (finger tight) and the…”
  • In Step 6, “…that attach to the Oil Cooler only finger tight, install…” was “…that attach to the 886 034 Oil Cooler only finger tight, install…”
  • In Figure 2, “OIL COOLER” was “886 004”, “CYL #1 EXHAUST PIPE” was “EXH-1201”
  • KAI Page 49-19 REV 4: Deleted Steps 1 & 2, Figure 1.
  • Added Bottom Duct Seal label (previously on 49-21).
  • KAI Page 49-21 REV 4: Deleted, contents moved to 49-19.
  • KAI Page 49-22 REV 4: Deleted